Qorvo's PAC5210 belongs to Qorvo's Power Application Controller® (PAC) product family. This family features highly-optimized SOC devices that can implement a BLDC or PMSM programmable motor controller and driver in a single integrated IC.
The product integrates a FLASH-based MCU, Power Management, open-drain drivers and signal-conditioning components in a single product. PAC5210 is optimized toward high-power IPM-based inverter systems.
This product contains a 50MHz Arm® Cortex®-M0 with 32kB of FLASH that can be used to implement high-performance motor control and supervisory applications. The MCU also contains motor control peripherals such as 10b 1MSPS dual auto-sequencer ADC and PWM timers with hardware dead-time insertion. The Multi-Mode Power Manager™ (MMPM) contains a 600V Flyback DC/DC controller and power management components for powering the IC and other PCB system power supplies. The Application-Specific Power Drivers™ provide integrated open-drain drivers for driving external relay devices. The Configurable Analog Front-End™ (CAFE) provides signal-chain components such as differential and single-end amplifiers, comparators and DACs.
|电源输入电压(V)||5.2 to 52|
|电源拓扑||600 V AC/DC Flyback|
|栅极驱动器 (开漏)||3 @ 23 V / 40 mA|
|微控制器||50 MHz Arm® Cortex®-M0|
|MCU ADC||10b, 1MSPS SAR|
|信号链 ADC 通道||11|
|封装(mm)||8 x 8|
The ET-UARTSWD adapter is the preferred adapter for evaluation of PAC devices/firmware and combines a USB to UART adapter with SWD debugger connector adaptation into a single board with isolation. The ET-UARTISO-1 adapter provides only the USB to UART adapter with isolation for Qorvo application GUI communications.
The ET-UARTSWD isolated communications and debugging interface unifies two modules into one. Previously, interfacing a PC Computer to any of Qorvo's PAC5xxx Evaluation Modules required one module to enable UART based serial communications and a second module to allow for in-system debugging and FLASH memory programing.
The ET-UARTISO-1 adapter is a USB to UART adapter for Qorvo application GUI communications with the PAC device UART, and can be used for evaluation and debugging of PAC applications.
Qorvo has partnered with Flash Programmer solution providers to support our Intelligent Motor Control PAC product families. These proven tools are suitable for emerging and high volume product manufacturing. Both package level (socketed) and board level Flash programming solutions are available.
Qorvo will support other vendors familiar with Arm® Serial Wire Debug (SWD) protocol to add PAC product compatibility on their existing Flash programmer platforms. For details, please contact Qorvo Sales.
|PAC52xx Software Development Kit
|Installer for the PAC52xx Software Development Kit (SDK) that provides register level definitions and peripheral driver APIs for developing Arm M0 application firmware on all PAC52xx devices. The PAC52xx SDK is a unified SDK that supports Keil µVision IDE, IAR Systems Embedded Workbench for Arm (EWARM) IDE, and GCC tool chains.|
|PAC52xx Example Code
|Installer for the PAC52xx Example Code that provides a simple source code example for getting started with the following IDE projects: Keil MDK (µVision), IAR Systems Embedded Workbench for Arm (EWARM), and Eclipse.|
Development of application firmware for PAC52xx Arm® Cortex® M0 is made easy with standard integrated development environments (IDEs). Several of the most popular IDEs contain support for PAC52xx devices including Keil uVision, and IAR Systems Embedded Workbench for Arm®. Eclipse development is possible using J-Link by downloading and installing the "Eclipse with PAC support" package.
|PAC52xx Keil IDE Guide
|Guide for installing Keil uVision for development of PAC52xx application firmware.|
|PAC52xx Keil .pack v1.0.9 to v2.0.0 upgrade
|Guide for upgrading the Keil uVision PAC52xx pack from v1.0.9 to v2.0.0.|
|PAC IAR Support
|PAC IAR Systems Embedded Workbench IDE installation guide and patches.|
|Eclipse with PAC Support
Version: v1.1.0 2019-03-27
|Installer for Eclipse and supporting plugins for development on the PAC family of devices.|
|Segger J-Link Support
|PAC support files for Segger J-Link debuggers.|