PAC52711

    70V BLDC Motor Controller & Driver with Advanced Production Features

    关键性能

    • 50MHz Arm Cortex M0
    • Advanced Cycle-by-Cycle Protection
    • 32kB Flash, 8kB SRAM
    • 1 x Differential PGA (x1 to x48)
    • 70V Buck/SEPIC DC/DC Controller with external NCH FET
    • 4 x Single PGA (x1 to x48)
    • 5V/200mA system supply
    • Programmable over-current shut-down
    • 3 High-side 70V 1.2A(source)/1.8A(sink) gate drivers
    • Programmable comparator hysteresis and blanking
    • 3 Low-side 20V 1.2A(source)/1.8A(sink) gate drivers
    • Hardware based nBRAKE and nDRVDIS control
    • Vds Sensing
    • Simultaneous Sample and Hold for 3 Phase

    Qorvo's PAC52711 expands Qorvo's broad portfolio of full-featured Power Application Controller® (PAC) products - highly optimized System On Chip (SOC) for controlling and powering next generation smart energy appliances, devices, and equipment – by adding new features such as VDS Sensing, Cycle By Cycle (CBC), Enhanced Sample And Hold (S&H), Windowed Watchdog Timer, hardware based nBRAKE and nDRVDIS for safety based applications with external safety MCU support. This application controller integrates a 50MHz Arm® Cortex®-M0 32-bit microcontroller core with Qorvo's proprietary and patent-pending Multi-Mode Power Manager™, Configurable Analog Front End™, and Application Specific Power Drivers™ to form the most compact microcontroller-based power and general purpose application systems.

    The product's microcontroller features up to 32kB of embedded FLASH and 8kB of SRAM memory, a high-speed 10-bit 1µs analog-to-digital converter (ADC) with dual auto-sampling sequencers, 5V/3.3V I/Os, flexible clock sources, timers, a versatile 14-channel PWM engine, and several serial interfaces.

    特别应用

      • Industrial BLDC Motor Control (Pumps, Fans, Robotics)
      • Power and Garden tools
      • Small Appliances
      • E-mobility
    电源输入电压(V) 5.2 to 70
    电源拓扑 70V Buck
    栅极驱动器 (高端) 3 @ 70V - 1.2A Source / 1.8A Sink
    栅极驱动器 (低端) 3 @ 70V - 1.2A Source / 1.8A Sink
    栅极驱动器 (开漏) N/A
    微控制器 50 MHz ARM Cortex M0
    MCU 闪存(KB) 32
    MCU SRAM(KB) 8
    MCU ADC 10 bits 1MSPS SAR
    MCU GPIO 16 Digital GPIO's (3.3V and 5V tolerant) + 10 AIOx GPIO's
    MCU PWM 4
    串行接口 UART/SPI, I2C
    信号链差分放大器 1
    信号链单端放大器 4
    信号链 ADC 通道 10
    封装类型 TQFN, 48-pin
    封装(mm) 6 x 6
    RoHS Yes
    Lead Free Yes
    Halogen Free Yes
    ITAR Restricted No
    ECCN EAR99

    PAC52711EVK1 Evaluation Kit

    PAC52711EVK1

    Qorvo's PAC52711EVK1 development platform is a complete hardware solution enabling users, not only to evaluate the PAC52711 device, but also develop power applications revolving around this powerful and versatile ARM® Cortex®-M0 based micro-controller. The module contains a PAC52711 Power Application Controller (MCU) and its internal peripherals, including new features such as VDS Sensing, Cycle By Cycle PWM truncation, AIO7/8/9 Sample And Hold, Windowed Watchdog Timer, enhanced gate drive strength, as well as enhanced low Hibernate current. Most importantly, PAC52711 introduces the new advanced protection features for safety critical applications. Access to nDRVDIS and nBRAKE control signals, allow for redundant control units to take over motor operation while experiencing safety relevant conditions.

    To aid in the application development the PAC52711EVK1 offers access to each and every one of the PAC52711 device's signals by means of a series of female header connectors.

    The PAC52711EVK1 can be used with various Graphical User Interface (GUI) software suites to externally control particular application's features over the PAC52711 UART interface. Provided with the development platform, the ET-UARTSWD module adds fully isolated USB to UART Virtual COMM Port, as well as access to the PAC52711’s SWD port through a fully isolated bidirectional channel which allows most SWD program/debug modules to interconnect with the system. 

    PAC52711EVK1 Schematics, Layout, BOM, Gerber Files

    PAC52711EVK1 Altium Project Files

    Supporting Evaluation Tools

    ET-UARTSWD

    The ET-UARTSWD adapter is the preferred adapter for evaluation of PAC devices/firmware and combines a USB to UART adapter with SWD debugger connector adaptation into a single board with isolation. The ET-UARTISO-1 adapter provides only the USB to UART adapter with isolation for Qorvo application GUI communications.

    ET-UARTSWD

    The ET-UARTSWD isolated communications and debugging interface unifies two modules into one. Previously, interfacing a PC Computer to any of Qorvo's PAC5xxx Evaluation Modules required one module to enable UART based serial communications and a second module to allow for in-system debugging and FLASH memory programing.

    Download ET-UARTSWD User Manual

    PAC5xxx Flash Programmer Tools

    Qorvo has partnered with Flash Programmer solution providers to support our Intelligent Motor Control PAC product families. These proven tools are suitable for emerging and high volume product manufacturing. Both package level (socketed) and board level Flash programming solutions are available.

    Qorvo will support other vendors familiar with Arm® Serial Wire Debug (SWD) protocol to add PAC product compatibility on their existing Flash programmer platforms. For details, please contact Qorvo Sales.

    Elprotronic Logo Leaptronix Logo
    Xeltek Logo Zeztek Logo

    PAC52xx Software

    PAC52xx BLDC Application Firmware
    Version: v2.4.0
    Installer for the PAC52xx BLDC application firmware, which implements sensored BLDC and sensorless BEMF motor control on all members of the PAC52xx family. The installer contains example application source code, Windows graphical user interface (GUI), and documentation to allow the user to configure the system to work with their target motor. Project files for IAR Systems Embedded Workbench for Arm (EWARM) and Keil uVision are included.
    PAC FOC Application Firmware
    Version: v4.4.3
    Installer for the PAC FOC application firmware designed to show case motor control using sensorless Field Oriented Control (FOC) on all PAC devices. The installer contains example FOC application source code, Windows graphical user interface (GUI), and documentation to allow the user to configure the system to work with their target motor. Project files for IAR Systems Embedded Workbench for Arm® (EWARM), Keil uVision and Eclipse are included. The FOC application provides a configurable set of features to meet many different application requirements such as sensorless position/speed estimator, start-in-motion (SIM), three or single shunt operation, open phase detection (OPD), field weakening and others.
    PAC52xx Software Development Kit
    Version: v2.8.1
    Installer for the PAC52xx Software Development Kit (SDK) that provides register level definitions and peripheral driver APIs for developing Arm M0 application firmware on all PAC52xx devices. The PAC52xx SDK is a unified SDK that supports Keil µVision IDE, IAR Systems Embedded Workbench for Arm (EWARM) IDE, and GCC tool chains.
    PAC52xx Example Code
    Version: 2019-05-03
    Installer for the PAC52xx Example Code that provides a simple source code example for getting started with the following IDE projects: Keil MDK (µVision), IAR Systems Embedded Workbench for Arm (EWARM), and Eclipse.
    PAC52xx ActiveFlashLight™ Bootloader
    Version: v1.2.1
    Installer for the PAC52xx ActiveFlashLight™ Bootloader that provides source code and example projects for in-system FLASH programming using the UART peripheral. Supported IDEs are Keil MDK (µVision), IAR Systems Embedded Workbench for Arm (EWARM), and Eclipse.

    PAC52xx IDE Support

    Development of application firmware for PAC52xx Arm® Cortex® M0 is made easy with standard integrated development environments (IDEs). Several of the most popular IDEs contain support for PAC52xx devices including Keil uVision, and IAR Systems Embedded Workbench for Arm®. Eclipse development is possible using J-Link by downloading and installing the "Eclipse with PAC support" package.

    PAC52xx Keil IDE Guide
    Version: 2018-08-21
    Guide for installing Keil uVision for development of PAC52xx application firmware.
    PAC52xx Keil .pack v1.0.9 to v2.0.0 upgrade
    Version: 2018-02-22
    Guide for upgrading the Keil uVision PAC52xx pack from v1.0.9 to v2.0.0.
    PAC IAR Support
    Version: 2019-07-31
    PAC IAR Systems Embedded Workbench IDE installation guide and patches.
    Eclipse with PAC Support
    Version: v1.1.0 2019-03-27
    Installer for Eclipse and supporting plugins for development on the PAC family of devices.
    Segger J-Link Support
    Version: 2019-10-23
    PAC support files for Segger J-Link debuggers.
    OpenOCD Support
    Version: 1.0.1 2020-11-02
    PAC support files for miscellaneous debuggers.

    我们随时提供帮助